LML-S

• Sensor for limit value detection in liquids
• Media contacting parts of stainless steel
• Mounting without removing the float (G5 and G6)

Function

• The device is a sensor for limit value detection in liquids.
• A ring magnet integrated in the float activates the contacts inside the probe tube via its magnetic field. If the probe strays outside the range of the mechanical contact, it reverts to the output status.
• The skipping of switching points caused by abrupt level changes can be avoided using snap-on set collars on the probe tube. The same set collars are also used for latching contact operation.

Pepperl+ Fuchs Magnetic Immersion Probe for Limit Value Detection

Connection

Change-over contact

Dimensions

Technical Data

General specifications
Function principle		ring magnet as switching element in the float, reed contact, change-over contact number of contacts: – version LML1: 1 contact – version LML2: 2 contacts – version LML3: 3 contacts
Series		LML-S
Supply
Rated voltage	Ur	250 V AC/DC
Current consumption		1 A
Power consumption		40 VA
Output
Connection		This device may be used with any sequential circuit, as long as the circuit can support the electrical circuit values of the switching elements.
Directive conformity
Low voltage
Directive 2014/35/EU		EN 61010-1:2010
Conformity
Degree of protection		IEC 60529:2000
Operating conditions
Installation conditions
Switching point		position according to specification
Process conditions
Process temperature		version LML: -30 … 150 °C (-22 … 302 °F) version LML-PVC1: -10 … 80 °C (14 … 176 °F)
Process pressure (static pressure)		≤ 25 bar (362.6 psi)
Density		version S2: ≥ 0.8 g/cm3 version S3: ≥ 0.7 g/cm3
Ambient conditions
Ambient temperature		-20 … 70 °C (-4 … 158 °F)
Mechanical specifications
Degree of protection		IP66 / IP68
Connection		version LML: terminal box, max. 9 terminals version LML-PVC1: connection cable 1 m (3.3 ft), 0.75 mm2
Material		float, guide tube, process connection: stainless steel 1.4571/316Ti connection cable: PVC terminal box: aluminum die-casting
Dimensions		float: – version S2: cylinder ∅44 mm x 52 mm – version S3: ball ∅52 mm guide tube: ∅12 mm, max. length 3000 mm terminal box: 80 x 75 x 55 mm
Process connection		thread G3/8A, G1-1/2A, G2A to DIN/ISO 228/1
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Accessories
Designation		– LML-Z11 set collar, 1.4571/316Ti – LML-FS2 float, cylinder, Ø44 mm x 52 mm, 1.4571/316Ti – LML-FS3 float, ball, Ø52 mm, 1.4571/316Ti

Type Code

The post Pepperl+ Fuchs Magnetic Immersion Probe for Limit Value Detection appeared first on Politek Vietnam Import Export Services Trading Company Limited.

The post Bucher Hydraulics External Gear Pumps, Series AP appeared first on Politek Vietnam Import Export Services Trading Company Limited.

The post Bucher Hydraulics Axial Piston Pumps AX appeared first on Politek Vietnam Import Export Services Trading Company Limited.

The post Blacoh SPILLSTOP, POLY/NORYL/POLY/NORYL appeared first on Politek Vietnam Import Export Services Trading Company Limited.

The post Blacoh 370 CU IN INLET STABILIZER, POLY/AFLAS appeared first on Politek Vietnam Import Export Services Trading Company Limited.

The post Blacoh AUTOMATIC INLET STABILIZER, 2.0″ NPT appeared first on Politek Vietnam Import Export Services Trading Company Limited.

The post Blacoh AODDAMPENER, 1″ NPT (AOD-10-NPT) appeared first on Politek Vietnam Import Export Services Trading Company Limited.

The post Blacoh AODDAMPENER, 1″ (AOD-10-BSP) appeared first on Politek Vietnam Import Export Services Trading Company Limited.

• HORSEPOWER: 1.0 HP
• VOLTAGE: 230 V
• PHASE: 1 Ph
• HERTZ: 60 Hz
• RPM: 3450 RPM
• AMPS: 6.0
• SOLIDS HANDLING: 1/2″ spherical solid
• CORD LENGTH: 50′
• MAX HEAD: 50′
• MAX FLOW RATE: 86 GPM
• IMPELLER TYPE: Non-clogging vortex

The post ZOELLER 4140-0008 MODEL SUMP & EFFLUENT BE4140 appeared first on Politek Vietnam Import Export Services Trading Company Limited.

Linear Low Density Polyethylene Plastic Tubing – LLDPE

I.D. = Inside Diameter    O.D. = Outside Diameter

Temperature vs. Working Pressure Relationship of LLDPE

LLDPE Polyethylene Tubing (Natural and Black)

The post Walchem LLDPE Tubing Part for the Metering Pumps appeared first on Politek Vietnam Import Export Services Trading Company Limited.